A faulty regulator restricts the gas flow and the geyser will not ignite due to insufficient gas. Buy a good quality regulator. … The gas in these cylinders has a lot of impurities (your flame will be very yellow/orange and not blue) and gas geysers are sensitive to having the correct gas mixture.

How do you ignite a gas geyser?

Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.

How does a gas geyser igniter work?

How does it work? Gas geysers heat the water instantly as it is demanded, as soon as a hot water tap is opened, and the water flows through the pipes at a sufficient flow it triggers a sensor inside of the gas geyser, a tap with a slow leak will not trigger the sensor, igniting the gas burner.

How do you troubleshoot a gas geyser?

Check your gas cylinder hasn’t run out of gas. If you have recently replaced your gas cylinder, you may have a vacuum lock. To clear this, remove the gas pipe from the regulator & switch on the gas cylinder for a few seconds. Switch off the cylinder, reconnect pipe & switch cylinder back on.

How do you light a pilot light?

1. First, locate the pilot valve on the furnace. …
2. Find the gas valve and turn it to the “off” position. …
3. Turn the valve to the “pilot” position.
4. Press and hold the reset button.
5. If the reset button fails, ignite the lighter.

How do I know if my geyser is not working?

No hot water It is a very common problem associated with a geyser. There are 2 heating elements inside a geyser that heat water. If the power supply in your home is fine but there is no hot water from geyser, it indicates that the heating elements have failed. Another reason for no hot water is a faulty thermostat.

What to do if geyser is not working?

First, reset any tripped circuit breaker, and replace any blown fuse. Next, check if power is being supplied to the electric water heating element thermostat. Test the element, and if it’s faulty, replace it.

How long does a gas geyser last?

Based on the usage of 2kg’s per day that i got of the 9kg, a 48kg cylinder should only last approx 24 days.

Does a gas geyser need a pressure control valve?

To protect the geyser, you must have pressure regulator valves fitted to you houses water supply. Low water pressure is more problematic than high pressure because it has a two-fold affect on gas geysers. … Smaller standard/ manual Gas Geysers , will switch off when the pressure fluctuates.

How do you remove an airlock from a gas geyser?

1. You must first attach the hosepipe to the broken tap and then fit its other end to a working tap.
2. Turn on the broken tap and this will help breaking the airlock. …
3. If this works, then first remove the hose off the highest tap and not the lowest.

Article first time published on

How much gas does a gas geyser consume?

The average 4 people home with a force-driven gas geyser will consume about 48 kg’s of gas in the winter and 19 kg’s of gas in the summer with a 5-10 minute shower. If you have a natural draft gas geyser you can expect higher consumption if the unit’s settings are not optimized to efficiently use gas.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

How much does it cost to replace thermocouple?

It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.

Does gas turn off when pilot goes out?

This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out. … If the pilot light goes out for any reason, the current stops, the valve closes, thus preventing any gas from leaking.

How do you know if the pilot light is on?

If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.

How much does it cost to relight a pilot light?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

How long should it take to light a pilot light?

To light a pilot light, first turn the gas control valve to off and wait 5 to 10 minutes until all the gas fumes are gone. Once you’ve made sure there’s no gas coming out, hold a lit barbecue lighter or long match next to the pilot light tube inside your furnace while turning the gas control knob to pilot.

Should the pilot light always be on in a gas heater?

Most furnaces with electronic ignition have a device called a hot surface igniter. … The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.

How do you flush a geyser?

1. Turn the Knob on Your Hot Water Heater’s Thermostat to “Off” …
2. Turn Off Gas to Hot Water Heater. …
3. Turn Off the Cold Water Supply to Hot Water Heater. …
4. Turn on the Hot Water in a Sink or Tub. …
5. Connect Garden Hose to Drainage Spigot. …
6. Turn on Spigot and Drain. …
7. Flush.

Can you use a mixer on a gas geyser?

YES, GAS GEYSERS CAN BE USED WITH MIXER UNIT TAPS! … Option One is to always start the mixer tap at it’s hottest position. After a few seconds, SLOWLY tap in the cold water. If the cold water is allowed in too fast, it tends to push the hot water back to the gas geyser.

How do you adjust the water pressure on a gas geyser?

Adjusting Water Pressure To do this, you need to find the pressure regulator on the incoming water line, which usually isn’t far from the water heater. You increase pressure by loosening the locknut and turning the adjusting screw clockwise.

How long will a 9kg gas bottle last on a gas geyser?

This converts into 0.555 kg/h of lpg consumption. Therefore a 9 kg bottle would last 16 hours of continuous usage with all burners operating.

Which gas geyser is best?

S. NOModel NamePrice1Orient Electric Techno-DX 5.5 litres Gas Water Heater₹ 5,1002Hindware Eveto 6L ISI Gas Water Heater₹ 4,1753SURYA ROSHNI HEATX-I INSTANT GAS WATER HEATER₹ 4,5504V-Guard 6 L Safeflo PRIME Gas HEATER(White)₹ 4,875

Which is better solar or gas geyser?

Solar hot water systems can provide between 50 and 90% of your hot water needs. … Gas Geysers produce about a third of the greenhouse gas emissions of electric storage hot water systems. Gas Geysers are very cost and energy efficient because they only use gas when hot water is actually being used.

Will an airlock clear itself?

Airlocks do sometimes fix themselves, but it isn’t a risk worth taking. Airlocks occur when air becomes trapped in the hot water or central heating system. Vapour becomes caught in a high point of the pipework because the gas is less dense than the water in the system.

How do you release air trapped in water pipes?

Start with the faucet that’s closest to the shutoff valve and work your way to the farthest faucet. Open each hot and cold faucet about halfway to let the air run out. Remember to flush all the water out of the toilets, too.

How do you clean a clogged geyser?

1. Turn the Water Heater Off. …
2. Turn the Cold Water Valve Off. …
3. Let the water cool. …
4. Attach a drain or garden hose to the drain valve on the side of the tank. …
5. Place the end of the hose in a bucket or drain. …
6. Turn on a faucet (or two) …
7. Start draining the tank by turning on the drain valve.

Which is cheaper electric or gas geyser?

Gas geyser cost and lifespan Gas geysers are less expensive than the electric geyser. Bajaj Gas Geyser is one of the best gas geyser comes under price Rs. 4,800.

Is a gas geyser cheaper than electric geyser?

The Pros and Cons of both types of geysers can easily be seen when viewing the table provided above. Gas geysers are inherently known for saving money in the long term as it does not use electricity to heat water, but the requirements to ensure the safe operation of a gas geyser may not be possible in all households.

How much gas does a gas geyser use per hour?

Model NamePH-203EWHInstallation TypeOutdoor, wall mountedGas Consumption NG21-153 MJGas Consumption LPG0.41-3.1 kg/hourCapacity2.5-20 L/min