One of the most common reasons a washer won’t spin clothes is an imbalanced wash load. To protect against damage, a spin cycle won’t engage when your machine senses an unbalanced load. If there are too few items in the washer or if it’s overloaded, the load will be unstable, and the spin cycle won’t start.

Why is my washing machine washing but not spinning?

Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.

How do I put my Electrolux washer in diagnostic mode?

Electrolux Diagnostic Mode * Press the Cancel button to enter standby mode and enable diagnostic entry. * Within 10 seconds after pressing Cancel , press any button to wake up the control. button under the display simultaneously for 3 seconds to enter the diagnostic mode.

Why won't my washing machine agitate or spin?

Common solutions for: My Washer Won’t Spin or Agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. … If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

How do I reset my Electrolux top load washer?

Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds.

How do you fix an e11 on an Electrolux washing machine?

1. Check the water supply to ensure that the water pressure is proper. …
2. Clean the filter in the inlet hose next to the tap. …
3. Ensure the correct position of the drain hose. …
4. Ensure correct drain height. …
5. Clean the pump and filter. …
6. Check for blocked drain.

How do I reset my Electrolux dishwasher?

On a display like this to reset the appliance, press and hold the On/Off button on the appliance for 3 seconds. This will reset the appliance and clear any previously set programmes. On a display like this to reset the appliance, press and hold the On/Off button on the appliance for 3 seconds.

Why does my Electrolux washing machine keep pausing?

Common solutions for: Electrolux Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.

How do I reset my Electrolux dryer?

To reset your Electrolux dryer, press and hold the “temperature” and “dryness” buttons simultaneously. Keep these buttons depressed for at least six seconds to reset the machine. If this doesn’t clear your error code, you likely need service.

Article first time published on

How do you reset a computerized washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

What are common problems with washing machines?

• It Bounces Around. …
• It’s Noisy. …
• Clothes Are Getting Ripped. …
• Improper Or Slow Draining. …
• My Washing Machine Won’t Spin. …
• There’s No Water. …
• The Door Won’t Open. …
• It’s Smelly.

How do I reset my washing machine motor?

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
3. The motor has now been reset and is ready for you to start a cycle.

Why is my washing machine motor not working?

In most cases, motor problems in your washing machine are going to be caused by worn carbon brushes. These are designed to come into contact with the moving part of the motor, which is called the armature, and pass power through it but they do wear down over time so obviously they will need to be replaced.

How much does it cost to replace a washing machine motor?

Washing Machine Motor Repair Cost If a part of the motor, like the coupling, just needs to be fixed, the cost may be under $100. However, a washing machine motor replacement cost runs an average of $325 to $500.

What does Error 11 mean on my Electrolux washer?

The code means the washer took too long to fill. It could be one of three problems, either the machine isn’t filling with water, or won’t fill with enough water or it has a draining issue.

What does E11 mean on my washing machine?

An E11 error code on a Hoover washing machine will indicate that you have a fault with the drying sensor. If the drying sensor is damaged or faulty then you will find yourself with a washer dryer with won’t dry your clothes after they have been washed.

What does e mean on Electrolux washing machine?

Electrolux Washing Machine – E – Drain Pump Error – Water Level Does Not Decrease To Reset Point Within 15 Minutes From Draining Water From The Washer. –

Why is my washing machine not washing?

A common reason why your washing machines is not cleaning clothes properly is because the line leading from the detergent tray to the drum has become clogged up with washing up powder. This means that just a small amount of detergent actually reaches the drum – the rest of it becomes stuck behind the blockage.

How do I turn off the child lock on my Electrolux washing machine?

It is easily resolved by the following instructions: To activate/deactivate this option, touch the Stains/Prewash (10) and the Extra Rinse (7) buttons simultaneously in a fast and consistent manner until the padlock no longer displays on the LED display.

Why does my Electrolux dryer keep stopping?

Filling enough laundry: If there is not enough clothing in the drum, the drum may be unable to detect it and the tumble dryer will end the cycle. … This is the most efficient way to use the tumble dryer’s energy.

Do dishwashers have a reset button?

Yes, you can reset your dishwasher by pressing the Start/Reset button on the appliance and waiting a few minutes. If your dishwasher still doesn’t start, you may need to reboot the entire system by turning off power to the appliance at the house circuit breaker or fuse box.

Why is my Electrolux dryer not spinning?

The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear.

Why does Electrolux dryer blink?

Check if the door is fully closed If the door is not completely closed, the start/pause button will simply flash and the cycle will not start.

Where is the dryer reset button?

Often, dryers are equipped with a reset button on the control panel.