The vast majority of new TRV’s are bidirectional and can be fitted to either the flow or return, but it is always good practice to fit them to the flow side. If a non bidirectional TRV is fitted on the return side it will create a vibrating sound as the water tries to flow though it.

Which side of a radiator should a thermostatic valve be fitted?

However, it’s always best practice to fit the TRV on the flow pipe that enters your radiator. If a non-bi-directional thermostatic valve is fitted to the return side of the radiator, it can make a loud vibrating noise when water tries to pass through it.

Which way does radiator valve go?

Turn valves clockwise to turn your radiator off and anticlockwise to turn it back on. Turning your radiators off is easy.

Which side of the radiator is the flow?

The flow of a radiator is typically on the left as you look at it stood up or attached to the wall.

Does it matter which way round a radiator goes?

A normal radiator or towel it doesn’t matter. If the radiator is not fitted, then the tails will not heat up. Fit the radiator, if it’s the wrong way round, all you have to do is swap the rad valves round – I think the instructions will just be referring to the TRV’s, nothing to do with the radiator itself.

Does it matter which side of radiator flow and return?

The vast majority of new TRV’s are bidirectional and can be fitted to either the flow or return, but it is always good practice to fit them to the flow side. If a non bidirectional TRV is fitted on the return side it will create a vibrating sound as the water tries to flow though it.

Are radiators directional?

Mistake 2 – Orientation of the radiator Some radiators can be installed in any orientation, but others have to be installed in a specific orientation.It is important to know whether the radiator you have selected.

Do both valves on a radiator need to be open?

You should open both of the valves on all of your system’s radiator when you are starting the radiator balancing process. … Once this is done your radiator system should be fully balanced and your radiators should heat up evenly and efficiently.

Which valve is which on radiator?

One valve accounts for the amount of hot water that enters the radiator. The other valve, referred to as the lockshield valve, balances the system by regulating how much heat the radiator gives off.

Which side is lockshield valve?

The lockshield valve, on the side of the radiator opposite the on/off valve, may be adjusted to balance the output of your heating system. The lockshield itself is the plastic cap that covers the valve to ensure that you don’t accidentally change the setting once you’ve adjusted it.

Article first time published on

Is the lockshield valve in the flow or return?

A lockshield valve (LSV) is 1 of 2 radiator valves that control the flow of hot water through each radiator. It’s typically placed on the return pipe, and derives its name from the plastic cap that protects the valve from being accidentally turned.

Can a radiator be installed backwards?

A word about installation: It is possible to install an engine fan backwards. … That is, if a correctly installed fan draws air through the radiator, an incorrectly installed fan still draws air through the radiator – it does not blow air through the radiator. Here is a picture of a fan correctly installed on its drive.

Do vertical radiators have a flow direction?

It is very unlikely they have dedicated ‘sides’ and should be fitable either way around. Ditto with these valves – the TRVs are bi-directional so can be fitted to either end, flow or return.

Should both sides of the radiator be hot?

The radiator rejects heat across its width (face). It is normal for the two rad tanks to be unequal temperature. It is normal for the passenger side tank to be warmer than the driver side rad tank.

Do you bleed a radiator when it is on or off?

Turn off your heating. You can’t bleed a radiator when the heating is on, as it may be too hot to touch. You could also get hot water spraying out of the radiator. Use your radiator key to turn the valve at the top of the radiator.

Is radiator valve same as lockshield?

The Lockshield valve restricts hot water flow to radiators to help balance the entire system as a whole. Other radiator valves can be used to help adjust the temperature of a radiator to help heat or cool a room. … In doing so, you will be able to pick the radiator and radiator valve that is most suitable for your needs.

What happens if all lockshield valves are fully open?

On most radiators, this is the valve you can’t turn by hand. By closing a fully-open lockshield valve by a few turns (with a pair of grips or screwdriver), you can slow down the rate at which water enters the radiator and reduce the speed with which it gets hot.

Should radiator lockshield be fully open?

Most lockshield valves have a plastic or metal cover. You should remove these and open all of the lockshield valves completely. This requires that you turn them anticlockwise. You should also fully open the TRVs (thermostatic radiator valves).

Where is the thermostatic radiator valve?

Thermostatic radiator valves are commonly referred to as TRVs and are used to control the air temperature of different rooms – you will normally find them on the side of your radiators. TRVs are just one of a number of heating controls, which allow homeowners to heat their homes more efficiently.

How do you bleed radiators with thermostatic valves?

1. Turn off the heating. …
2. Always start with the radiators at the lowest level. …
3. Fully open the thermostatic valve.
4. Start the bleed. …
5. Tighten the screw without forcing it when the heating water is clear again, as if you were closing an ordinary tap.

What temperature is 3 on a radiator?

Valve positionReference temperatureRecommended setting for2-318°CBedroom319-20°CKitchen3-420-21°CLounge, child’s bedroom422°CBathroom

Can a radiator have two lockshield valves?

As long as there is other radiators on the system and they aren’t all closed down you shouldn’t have a problem.

How do you balance a radiator with TRV on return?

If the valve at the return end is a TRV it may have an internal balancing adjustment screw. If it does, adjust it to the half closed position. If the TRV has no internal balancing screw, you will have to balance the radiator using the lockshield valve at the other end of the radiator, even though it is on the flow end.

Do all radiators have a lockshield valve?

Unless your radiators have TRVs fitted, they will usually have a wheelhead and a lockshield valve, one on each end.

What happens if flow and return are reversed?

If the pipes are reversed, the sensor will record the lower temperature and could compensate to make up the difference. This can result in unwanted noise, or overheating and inefficiency.