The Daily Pulse.

Your source for accurate, unbiased news and insightful analysis

entertainment

Where do I find the in line fuses on a Kwikee?

By William Brown |

Where do I find the in line fuses on a Kwikee?

I called the Camping World (over 8 hours away & not headed in that direction) that installed them & the service writer agreed it appeared to be an “electrical issue” & suggested I look for an in-line fuse, but I can’t locate any & it’s darn-near impossible to trace the wiring as they are all wrapped together leading into the engine compartment.

What are the step test procedures for Kwikee?

Troubleshooting and Test Procedures The step test procedures outlined in this tip sheet are provided to troubleshoot and test all Kwikee IMGL automatic electric step functions. The procedures are designed to initially check the basic functions of the step separately from the RV wiring to determine whether or not the step is malfunctioning.

What does warm motor mean on Kwikee step?

With Kwikee that is detected by the control board when the motor stalls due to reaching the stops and no position switch is involved. A warm motor would seem to imply that the power didn’t shut off like it should when the step reached the stop in the store position.

Why are the steps on my Kwikee not working?

There are several possibilities that could do what you have now. One is the motor failed, another the control board has failed, or for some reason the motor does not know the steps have reached the stored position and the motor has not powered down.

I called the Camping World (over 8 hours away & not headed in that direction) that installed them & the service writer agreed it appeared to be an “electrical issue” & suggested I look for an in-line fuse, but I can’t locate any & it’s darn-near impossible to trace the wiring as they are all wrapped together leading into the engine compartment.

With Kwikee that is detected by the control board when the motor stalls due to reaching the stops and no position switch is involved. A warm motor would seem to imply that the power didn’t shut off like it should when the step reached the stop in the store position.

There are several possibilities that could do what you have now. One is the motor failed, another the control board has failed, or for some reason the motor does not know the steps have reached the stored position and the motor has not powered down.

What are the fuses on a Ford chassis called?

On a Ford chassis fuse block, the fuses that supply things in the part added by the RV manufacturer are usually labeled “body builder” followed by what it feeds, or if not designated, just the words “body builder” so that may help to narrow it down.

Which is the best way to check fuses?

The best way to check fuses is by using an ohm meter and the good ones will read 0 ohms through them, with anything more than a few ohms being bad. There are several possibilities that could do what you have now.

Where to find the part number of a Kwikee step?

HEET To identify the standard step part number or series number, look for the Kwikee label under the step on the mounting surface that attaches to the coach. The label will show the part number of the step. You may have to have the step extended to see the label. Below are a couple examples of different labels used on the steps. EXAMPLE 1:

What does it mean if there is an inline fuse?

First of all, if there is an inline fuse, that usually means a fuse that is in one of those fuse holders that is not on a fuse block, like one of these.

On a Ford chassis fuse block, the fuses that supply things in the part added by the RV manufacturer are usually labeled “body builder” followed by what it feeds, or if not designated, just the words “body builder” so that may help to narrow it down.

Can you put a higher rated fuse on a camper?

Your camper or RV was designed by professionals with your safety in mind, as well as your convenience. Each electrical device was installed on an electrical line that could safely handle the load. Putting in a higher-rated fuse or breaker does not fix any problems.

First of all, if there is an inline fuse, that usually means a fuse that is in one of those fuse holders that is not on a fuse block, like one of these.