FL1/FL2. This code means any of the following: the flow switch is malfunctioning open (FL1) or closed (FL2), the filter cartridge needs to be changed or cleaned, or there is an “air lock” condition at the circulation pump intake.

How do you fix FL1 on a Jacuzzi hot tub?

Make sure you monitor the hot tub while it runs without filters to ensure that no debris gets pulled into the filter area and down into the pumps. If the FL1 error goes away after removing the filters, it is possible that your filters need to be cleaned or replaced. Clean and/or purchase new filters.

How do I reset my hot tub jacuzzi?

1. Locate the spa’s high-limit reset. This is a red button found on many spa packs. …
2. Press the high-limit reset button. …
3. Turn on your spa and observe its operation. …
4. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

How do you fix an f1 error on a hot tub?

Solution A: Increase the hot tub water level Switch off the power and remove the filters. After 20 minutes, switch the power back on and run the spa/jets without the filters to see if it clears the flow issue. If the flow clears, switch off the power again, replace the filter and then switch on the power.

What does F1 mean on a hot tub?

CODEERROR CODE DESCRIPTIONF1, F2(Vita Spa) Blown fuse; replace fuse 1 or fuse 2F24 hours daily filtration; system message, not an errorF48 hours daily filtration; system message, not an errorF612 hours daily filtration; system message, not an error

Why did flow fail?

In many cases, flows fail because of an authentication error. If you have this type of error, the error message contains Unauthorized or an error code of 401 or 403 appears. You can usually fix an authentication error by updating the connection: In the right pane, click on View Connections below How to fix.

Where is the flow switch on a hot tub?

The flow switch is located behind the outside walls of the spa and connected to the plastic piping.

Where is the reset button on a jet tub?

You will find a reset button typically on the heater unit. Usually there is a pilot light. When you’re ready to reset, push the button. Some spa units have a high limit switch which will turn off the spa heater if the thermometer fails.

What does flow error mean?

My hot tub has a flow error. All hot tubs are equiped with a way of detecting that there is water flowing through the heater. … A flow error is the most common type of problem that arises in hot tubs. There are lots of possible causes, but the most common are: Water issues: Dirty filters, low water levels, blockages.

Why is my hot tub not getting hot?

If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.

Article first time published on

Why does my hot tub say low flow?

For low flow spa error codes, check the filter, check the pump and check the valves to find if something is obstructing the water flow. … Low flow can also mean a low water level. Sometimes, it’s actually a just bad pressure switch or flow switch, or sometimes loose connections, damaged wires or wire connectors.

Why are my hot tub jets weak?

When jets start failing, the most likely case is that your hot tub pump is not working correctly. … Open the access panel and the airlock valve close to the pump. This releases air from the line and purge system, allowing more water to stream through the jets. Clogged filters or water intakes can also cause jet issues.

How do you test a flow switch?

1. Put cover on the flow switch and turn power on. Video of the Day.
2. Start flow through the designated system.
3. Observe flow in operation to determine if flow switch is working properly.
4. Repeat this process many times to ensure flow switch and designated system is in fact working accurately. Tip.

What does Flo mean on a Jacuzzi hot tub?

If you have a Hot Tub FLO Error Code, this usually means there is an issue with water flow in your hot tub.

How do you troubleshoot a flow switch?

1. Turn the unit off and unplug it from the power source for 30 seconds. …
2. Ensure the flow switch valve is open. …
3. Look at the water level in the hot tub. …
4. Clean out the filter. …
5. Check the output pressure and input pressure of the spa’s jets and filter.

How do you fix power automated?

1. Sign into Power Automate.
2. Go to Data > Connections.
3. Find the connection that’s used in your flow.
4. Select Fix connections, and then update the credentials for your connection if there is a Fix connection message next to the Status column.

How do you troubleshoot power automate flows?

1. Open your failed Flow’s run history and select the failed instance:
2. Locate the failed Flow and check the ‘INPUTS’; click ‘Show more’ to review all data.
3. Scroll down to review the ‘OUTPUTS’

How do I get an error in power automate?

1. Wrap the Actions in a Scope – note: wrap all your actions in a scope (or, at least any action that can possibly produce an error)
2. Add a Parallel action at the end and configure the run after for failed and timed out.

Why won't my Jacuzzi bathtub jets turn on?

If there is too little water, air could be working its way into the system through the jets. If you’ve checked your filter, water level, and the issue persists, you may have a clog in the line, or your pump is simply reaching the end of its lifetime and should be repaired or replaced.

How do you turn on an old Jacuzzi tub?

1. Set the water temperature for your bath. …
2. Fill the tub with water set to your temperature preference. …
3. Climb into the whirlpool bathtub carefully. …
4. Press the “On/Off” control on the side of the tub to turn on the pump and start the whirlpool jets.

How do I know if my hot tub fuse is blown?

You could perform a continuity check on the fuse. If it reads zero, the fuse is blown and should obviously be replaced. But even if it shows some reading it may be partially defective and you should replace it with a new one to see if it corrects the problem.

How do I know if my hot tub heater is working?

To test if a bad heater is causing your tripped breaker, you can disconnect the copper tabs (or wires) from the spa pack to the heater element. Once disconnected, turn the power back on. If the breaker stays on, you’ve determined that the heater is bad.

How do you turn up the temperature on a hot tub?

To adjust the thermostat, you simply press the button that increases or decreases the water’s temperature. Some hot tubs may use a mechanical thermostat to control the water temperature and you need access to the spa’s heater to adjust this thermostat.

Does hot tub heat up faster with jets on?

A hot tub heats up faster if the jets are turned on. This is because the water circulates with the jets on, which evenly disperses heat and prevents cold water from being trapped in the hot tub pipes.

How do I know if my hot tub has an airlock?

As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump.