What does a co error code on a refrigerator mean?

A CO error code on the display of the refrigerator indicates a communication error between the control board and the display. Unfortunately, there are no troubleshooting steps to resolve this issue. The unit will require a repair service, please visit our Request a Repair page.

What does no co mean on a Norcold refrigerator?

Occasionally the Norcold refrigerator can display an error message. The display will read “NO CO”, which probably means “Not Cooling”. It’s not a serious problem but it is a bit tricky to reset. The following procedure describes what to do if you ever see the “NO CO” error code displayed on the front of your Norcold refrigerator’s LED display.

What to do when your refrigerator says no co?

Press and hold the TEMP SET button on the fridge control panel. When ‘Er’ shows on the screen release the TEMP SET button. When ‘CL’ shows on the screen, wait five seconds and press and hold the TEMP SET button until ‘Er’ is shown on the screen again. Cycle the fridge off/on to see if the “no co” error is erased.

What does a 22 error code on a refrigerator mean?

This refers to the fan at the back, bottom of the refrigerator that discharges heat from the condenser. Unfortunately, there are no troubleshooting steps to resolve this issue. The unit will require a repair service, please visit our Request a Repair page. A 22 error code indicates a problem with compressor relay.

What to do if your refrigerator has no co fault?

1. Turn OFF the refrigerator. 2. Disconnect the following from power board: a. 12 Vdc positive and negative wires. b. AC power cord. c. Solenoid gas valve wires d. Spark/sense electrode assembly wires. 3. Remove the power board cover. 4. Reconnect 12 Vdc positive and negative wire. 5. Turn ON the refrigerator. 6.

How to reset a Norcold 1200lrim Hunker refrigerator?

Wait several minutes and then press the “On/Off” button to restore power. This will reset the refrigerator. Contact an authorized Norcold service center for assistance if the above steps do not reset the refrigerator, as a more complicated reset involving the hardwire power board may be necessary and requires professional assistance.

What does the Norcold 1210 error code mean?

Norcold 1210 refrigerator error codes. Fault Codes. Fault Code Meaning. Corrective Actions. No display. DC voltage is unavailable to the refrigerator control panel or the refrigerator is OFF. – That the refrigerator is ON. – That the battery charging equipment of the vehicle is operational.

What to do when you see an error code on a Frigidaire refrigerator?

There are many different model numbers of Frigidaire refrigerators (side-by-side and french doors) with digital displays so when you see an error code write down what is flashing or displaying. Don’t pull the power from the fridge if it shows an error code. If you pull the power plug it will erase the fault code.

Why does my Refrigerator have a Po error code?

First: Always unplug the refrigerator from power to avoid shock or damaging the control board (s) when troubleshooting your refrigerator. These 2 parts can cause the PO error code, we recommend to check these parts before replacing them. It can be either one that is causing the PO error code and beeping.

What to do when you get an error code on a whirlpool refrigerator?

There are many different model numbers of Whirlpool refrigerators (side-by-side, bottom-freezers, french doors) with digital displays so when you see an error code write down what is flashing or displaying. Don’t pull the power from the fridge if it shows an error code. If you pull the power plug it will erase the fault code.

What’s the error code on my KitchenAid refrigerator?

There is a CONFIRM button on the display and when I press it, it resets the PO error code and the beeping issue stops and all is good. However, 10 minutes later the error code “PO” displays once AGAIN and the fridge beeps continuously. The lights on the deli drawer are not working.