It’s good practice to point your return jets in a direction that will circulate the water in your pool. If your pool only has one jet, point the jet toward the skimmer and downward. This will circulate the water, and push the water at the bottom of the pool to the surface.

How do you set up pool jets?

Most people like to point the jets in a unified direction, clockwise or counterclockwise. On older pools, return jets might have been built on one side or end of the pool with the skimmer opposite the return jets.

What pressure should pool filter run at?

The pool filter pressure should be steady, operating in a range of +/- 10 psi. When it’s outside this range, very low or very high, then you know that something’s wrong. Some gauges allow you to set the clean and dirty range, or you can write it on the filter tank with a marker.

How do I increase circulation in my pool?

1. To ensure proper circulation, you need to switch on the pump for at least 8 hours a day. …
2. Make sure you size the pump, i.e: get a pump according to your pool volume. …
3. Just as you clean the pool, you also need to clean the pump and the filtration system. …
4. Your pool may have a cartridge filter.

What is a pool return jet?

Pool return jets are an integral part of your filtration system and if set properly, increase the circulation of your pool water and disrupts sediment buildup and debris from walls and the floor. Also, if you have an automatic floor vacuum when positioned properly, these jets can help the movement of the vacuum.

Why are my pool jets not strong?

The most common reason for weak jets is an air leak. An air leak would come from the suction side of the system. This would be the area between the skimmer and the pump. … The pump strainer, in most cases, should be full of water and have no visible air.

How strong should pool jets be?

The pressure in the recirculation system should be between 10 and 15 psi. If the gauge reading is below 5 psi, something is wrong, and if you’ve checked all the easy-to-fix problems first, you should suspect a leak.

How often should I backwash my pool?

Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. “When do we need to backwash?” – It is recommended to backwash your filter once every 4-6 weeks of regular use.

What are the 2 holes in skimmer?

The second hole in the skimmer is connected to a pipe called an equalizer. This pipe goes down approximately two feet and through the concrete wall of the pool. It prevents the pump from taking in air if the pool’s water level dips below the skimmer opening.

Should chlorinator be full of water?

The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.

Article first time published on

How do I know if my pool filter is working properly?

The easiest way to know if your pool’s filter is working properly is to check its pressure gauge on a daily basis. If the filter becomes clogged, it can suffer serious damage, which means your pool will not be cleaned and sanitized properly.

What causes high pool pressure?

High swimming pool filter pressure is usually the result of a lot of particles being filtered out of the swimming pool water. When pressure rises it is time to backwash the filter if you have that option with a sand or diatomacesous earth (DE) filter.

Why are my pool jets bubbling?

What are the most common reasons for pool air bubbles? … The pool water level is too low. The strainer pot lid isn’t on tight or its O-ring is loose/absent/compromised. The union between the valves and the pump isn’t tight or its O-ring is loose/absent/compromised.

What is the side of a pool called?

If an in-ground swimming pool is constructed of concrete, it will need coping, which is a cap for the edge of the pool. Besides simply being necessary, the coping provides an opportunity for a decorative accent, which can greatly enhance the appearance of the pool.

How deep should a pool return be?

Though returns have traditionally been placed 12 to 18 inches below the water’s surface, more professionals are recommending that they be installed closer to the floor.

How many skimmers should a pool have?

How many skimmers do I need? The Association of Pool and Spa Professionals (APSP) advises that there should be a minimum of one skimmer per 400 sq. ft. of pool surface area.

How many jets should a pool have?

A pool typically has two to three return jets where the water that filters through the circulation system returns to the pool. For effective circulation, it helps to have these multidirectional jets, because they allow you to determine the direction that the water returns to the pool.

How long should I backwash my pool?

Watch the pressure gauge for spikes. After the hose fills with water, backwash your sand filter for 2 – 3 minutes, or until water runs clear.

Why does my pool pump loses suction?

CLOGGED IMPELLER (Low PSI) – This problem is often overlooked. If the impeller becomes clogged with debris, water can’t rotate out the sides of the impeller. This decreases suction which reduces water flow through the pump. … See our guide on “How To Clean Out a Pool Pump Impeller”.

Should my skimmer valve be open or closed?

For the cleaner to operate at maximum efficiency, only the skimmer and cleaner valves should be open. No other valves should be open. So it is either main drain+skimmer or cleaner+skimmer. Never main drain+skimmer+cleaner all open at the same time.

How much suction should a pool skimmer have?

You should aim for a water level about 1/2 to 2/3 up the opening of the skimmer. Too low and you start to get gurgling sounds which are telling you that your pump is working way too hard at trying to keep the water flowing.

What is pool Putty?

Quick set pool putty is a one-time use product that includes resin and hardener together in a single tube. … This product is sometimes used for pool pump leaks. It is also useful for pool light leaks or to seal a loosened tile in or around the swimming pool area.

Should I Use main drain or skimmer?

Skimmer Vs. Drain. If the pool receives a lot of leaves and other debris, more suction may be required at the skimmer than the main drain to adequately strain debris floating on the surface. Conversely, if dirt on the bottom of the pool is the principal contaminant, more suction is required at the main drain.

Should you rinse after backwash?

Backwashing reverses the flow of water, lifts up and flushes the sand, and then expels the dirty water via a waste line into the ground or drain. In order to prevent residual blow back into the pool, once you’ve finished backwashing it’s highly advisable to rinse the filter.

How many hours a day should you run your pool pump?

Overall, the lessons learned today is you should run your pool pump an average 8 hours a day to properly circulate and clean your water. The pump should push your entire pool in gallons in this 8 hour period of time. Residential pool water only needs to be turned over once daily to have proper filtration.

How often should you change sand in pool filter?

On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.

What setting should my pool chlorinator be on?

Choose a mid-point setting on the 1-10 dial. The higher the setting, the greater the dissolution rate. A setting of 5 may be too high, and it depends on the number of tablets in the feeder. You could fill it full, with 15 tablets, and put it on a setting of 1-2, or add only 2 tablets and put it on a setting of 8-9.

What should my chlorinator be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

How many pucks are in a chlorinator?

It is easy to tell if you need more chlorine pucks in your skimmer basket. Since they dissolve, once they have disappeared just add more. Chlorine pucks also allow you to manually control how much chlorine is in your pool’s water. It is usually 1 chlorine puck for every 5,000 gallons of water.