Reset button—The furnace can also trip its reset button when there is a power outage. It’s usually a red or yellow button located inside the blower compartment near the motor. When it’s tripped it pops up. Push and hold the button for a few seconds.

Do you need to reset furnace after power outage?

When faced with problems with your gas furnace, you should always try restarting the unit first to see if the system goes back to normal. If not, troubleshooting your furnace yourself or reaching out to dependable Temecula heating services would be the best course of action.

Should I hit the reset button on my furnace?

The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.

Why my furnace is not working after power outage?

Power outages can cause these outlets to trip. Check to make sure that any GFI outlets attached to or near the furnace have not tripped. To fix this problem just press the reset button on the GFI outlet. Lastly, if the power was out for more than 5 minutes you may want to check that the thermostat did not reset.

Can a power outage damage a furnace?

Both power surges and power outages have the ability to damage electronics like your furnace and air conditioner. … In this scenario, too much power is coming into your home. Virtually every residence in America receives electrical power rated at 120 volts.

Why is my furnace blowing cold air after power outage?

Your furnace may be blowing cold air because the filter is too dirty. A dirty air filter blocks airflow over the furnace’s heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.

Where is the reset button on furnace?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

Where is the furnace switch located?

Most building codes require a furnace switch or “disconnecting means” within sight of the furnace itself. It’s usually mounted on the side of the furnace or a wall nearby.

How do you reset a furnace after overheating?

1. Turn down the thermostat to its lowest setting.
2. At the circuit breaker, turn off the power to the furnace.
3. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on.
4. If the pilot light was out, light a match to relight it.

How do you reset a furnace blower?

1. Step 1: Turn off the power to the furnace. …
2. Step 2: Remove the blower compartment cover. …
3. Step 3: Make sure the blower is completely cooled off. …
4. Step 4: Locate the reset button. …
5. Step 5: Press the button in (assuming that this is your issue and that the button has popped).

Article first time published on

How do you reset a heat pump after a power outage?

1. Make sure the heat pump is off. You can do this during the power outage.
2. Once power comes back on, turn the heat pump to the “Emergency Heat” setting. This will allow the compressor to warm up slowly and get the refrigerant warm enough to start flow freely again.
3. Wait.

Can a power outage damage HVAC unit?

A Power Outage Can Take Down Your Air Conditioner in a Second. This time of year can be dangerous for your air conditioner. Hurricanes, tropical storms, and even pop-up thunderstorms can take down power lines and also damage electrical equipment like air conditioners.

Why is my furnace not heating up?

Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up. If the blower is running but no heat is coming out, replace the filter.

Why is my furnace not lighting?

The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. … Then, remove the front panel to find the ignitor or ignition sensor. This is typically located near the burners. If the sensor or ignitor is dirty, it will need to be cleaned.

When should I reset my furnace?

If your furnace doesn’t have any air coming out at all and the pilot light is out, it’s worth it to try resetting the furnace. If this doesn’t work, there may be a problem with the thermostat setting, the power, or the gas line.

What happens if a furnace overheats?

The most serious risk of an overheating furnace is stress cracks in the heat exchanger caused by overheating. The vast majority of premature heat exchanger damage is due to overheating as the heat stress causes cracks near the welds and bends.

What does blower motor reset button look like?

Examine the exposed components in the furnace cabinet to locate the blower motor; look for a small silver box positioned toward the top of the cabinet. Mounted just above this box you should see a small round component with a raised red or white button at the center; this is the blower reset switch.

Is there a reset button on my heat pump?

So if your unit is off and not responding to your thermostat settings, your heat pump or air conditioner will most likely not have a reset button unless it’s a Rheem or Ruud unit and there are a few others that come with reset buttons.

How do I restore the power to my thermostat?

1. Turn off your thermostat. Before doing any other troubleshooting, start by finding your thermostat and turning it off. …
2. Locate and reset circuit breaker. …
3. Wait 30 minutes. …
4. Turn the thermostat back on.

How do you reset central air?

1. Power down your AC. Start at your circuit breaker panel and flip the breaker that powers your AC. …
2. Find the button. Most air conditioning units are equipped with a reset button. …
3. Hold down the reset button for 3 to 5 seconds and then release.
4. Restore power to your AC.

Can a power outage damage a thermostat?

If the thermostat setting is calling for cooling when the power is restored, the surge caused by a restoration of electricity can damage the heating, ventilating, and air conditioning system.

What do you do after a power surge?

1. Reset, unplug, and repower all electronic devices. …
2. Assess your home for any damages by inspecting your appliances, electronics, and power outlets.
3. Check your HVAC system for functionality and any damage.