To replace this belt, the deck should be off the lawn mower. … To remove the front of the belt from the engine pulley, you may have to remove the cap screw from the center of the pulley and PTO to the engine crankshaft.

Do you have to remove mower deck to replace Belt?

To replace this belt, the deck should be off the lawn mower. … To remove the front of the belt from the engine pulley, you may have to remove the cap screw from the center of the pulley and PTO to the engine crankshaft.

How many belts are on a riding lawn mower?

There are two belts on most riding lawnmowers. One belt connects the transmission of the lawn tractor to the driveshaft pulley and the other belt connects the mower deck to the driveshaft pulley.

How do you tighten the belt on a Poulan Pro riding lawn mower?

1. Roll the Poulan riding mower onto a flat surface. …
2. Lift the cover for the engine and remove the spark plug, using a socket wrench. …
3. Lower the mower deck.
4. Push in on the idler pulley underneath the engine. …
5. Remove the bolt from the housing on the deck.

How long does a lawn mower belt last?

A lawn mower is not complete without a belt. Good mower belts should last for about 3- 4 years. If you don’t have a quality mower belt, you need to get one to use it for this long. As you use a mower belt, you should also inspect it from time to time to confirm any signs of tear.

How do I know if my mower belt is bad?

1. The belt has s​​​ide wall damage. Mower belt edges should be smooth and even throughout the entire length of the belt. …
2. The belt has a glazed or bu​rned sidewall. …
3. The belt is​​ cracked.

What is the difference between a deck belt and a drive belt?

So, with the mower deck removed from the tractor, the “drive belt” would be the one still on the tractor. The mower deck itself will still have the internal “deck belt” which if you turn one blade by hand, all blades turn because that deck belt is what connects and drives all the blades together.

How do you tighten a drive belt?

Insert the pry bar above the alternator pulley. Apply gentle pressure upwards so that it adds tension to the drive belt. Once the drive belt is moved into its desired tension, tighten the adjustment bolt to lock the belt in place. Then, torque the adjustment bolt to the manufacturer’s specifications.

Why does my belt keep slipping off my lawn mower?

A lawn mower belt keeps coming off the mower because the belt guides and brackets are out of adjustment; debris is collecting under your pulleys and tensioners; the brackets, bearings or bushings are damaged, or the mower belt is worn.

Do zero turns have drive belt?

Zero turn mowers provide flexibility when mowing around landscape items and turns in your lawn. Keeping your zero turn mower running at its best requires replacement of the drive belt every 100 hours of operation. The drive belt becomes worn when grass and debris build up under the deck of the mower.

Article first time published on

What is the drive belt on zero turn mower?

Whatever you call it, its function is to transfer power from the engine to the transaxles, powering the drive wheels on a zero turn lawn mower. Without this belt, the wheels wouldn’t turn, and that’s why it’s important to check this belt for cracks and other signs of wear often and to replace when necessary.

How do I change the belt on my MTD riding mower?

1. Step 1: Prevent unintentional starting. …
2. Step 2: Adjust the deck height. …
3. Step 3: Take off the mower deck belt guards. …
4. Step 4: Take off the belt-keep rod. …
5. Step 5: Loosen the idler pulley nuts. …
6. Step 6: Snap a photo. …
7. Step 7: Take off the mower deck belt. …
8. Step 8: Install the new mower deck belt.

Are mower belts Universal?

There’s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.

What is the primary mower belt on a riding mower?

The ground drive belt connects the engine crankshaft to the transaxle pulley to drive the rear wheels. If the belt breaks, the lawn tractor won’t move. If the belt is worn, the lawn tractor moves sluggishly because the belt slips on the pulley.

Can a lawn mower belt stretch?

Yes, lawnmower belts can stretch. Continuous wear due to regular operation can cause them to elongate over time. When it stretches more than it should, it can result in the drive belts lose grip on the pulley system.

How long should a PTO belt last?

Most modern vehicles use belts made from ethylene propylene diene monomer, a synthetic rubber that lasts longer than older types of engine belts. Most belt manufacturers estimate the typical lifespan of an EPDM belt to be 50,000 to 60,000 miles, and some say it’s more than 100,000 miles.

How much does it cost to replace a drive belt?

Once the belt starts to wear thin or breaks, it will need replacing, if those parts are going to work as they should. You will pay between $120 and $160 for this replacement job. The labor should cost about $80, while parts will run you about $60.

How often should a drive belt be replaced?

How Often Should You Change the Belts in Your Car? It is often beneficial to change the drive belts in your car approximately every 60,000 to 100,000 miles. By undergoing annual car inspections, you can have your drive belts evaluated.

How much does it cost to replace a serpentine belt?

A typical serpentine belt start at around $25 and goes up to $75 at most. If you know some car repair basics, you could change the belt yourself, and it may save you paying labor charges somewhere between $75 and $120. All together, you’re looking at around $100 to $195 to replace your serpentine belt.

Why does the deck belt keep coming off my riding mower?

The drive belt may come off a riding mower because it is damaged or loose. … If broken or worn, the belt can break while the engine runs, and it can fly off at a great velocity, which is highly dangerous. Check the belt for looseness, cracks, fraying or separation from the rest of the assembly, and replace if necessary.